Distribution Amplifiers

RB-DA24MD

24 Way Mono Audio Distribution Amplifier

The RB-DA24MD is a 1U rack mount high performance 24 way audio distribution amplifier.

RK3_logo-optimized

About RB-DA24MD

The RB-DA24MD is a 1U rack-mount, high-performance 24-way audio distribution amplifier. It features two inputs that can be independently routed to 12 outputs each, or combined and sent to all 24 outputs.

The unit can operate in dual-mono mode (input 1 to outputs 1–12, input 2 to outputs 13–24) or mixed-mono mode, where both inputs are combined at a pre-set level and distributed across all outputs. In mixed-mono operation, three output level options are available via internal jumpers: -6dB, -3dB, or 0dB.

The XLR inputs and D-type outputs are electronically balanced but can also be wired for unbalanced operation. Each output is individually buffered, ensuring that a fault on one does not affect the others, and is protected against connection to both PoE (Power over Ethernet) and phantom power circuits.

Master gain controls for each input are accessible via rear-panel preset potentiometers, allowing adjustment from -15dB to +15dB – ideal for matching consumer and professional signal levels.

A front-panel LED indicates power status, while a rear-panel switch activates a 125Hz, 6dB-per-octave roll-off filter applied to both inputs.

Typical Applications

Distribute mono emergency audio signals to multiple powered monitors, to distribute a mono source (e.g. mic input converted to line) to many outputs, e.g. at a news conference.

Product Data

Technical Specifications

Audio Specification
Input impedance:
>20kΩ bridging (balanced)
Output impedance:
<50Ω
Maximum Input Level:
+28dBu
Maximum Output Level:
+28dBu
Frequency Response:
20Hz to 20kHz ±0.1dB (600Ω load, ref 1kHz)
Gain Range:
Adjustable -15dB loss to +15dB gain
Common Mode Rejection:
>66dB typically
LF Roll Off Filter                :
125Hz at 6dB/octave
Distortion:
0.01%THD @ 1kHz, red + 8dBu output
Noise:
-100dB unity gain, ref +8dBu output
Connections
Inputs:
2 x XLR 3 pin female (balanced)
Outputs:
2 x 25 way D-type plug (balanced, can be unbalanced)
Mains Input:
Filtered IEC, switchable 110-120V, or 220-240V, fused, 12W maximum
Fuse Rating:
Anti-surge fuse 100mA 20 x 5mm (230VAC)
Fuse Rating:
Anti-surge fuse 250mA 20 x 5mm (115VAC)
Equipment Type
RB-DA24MD
24 way mono distribution amplifier
Physical Specification
Dimensions (Raw):
48cm (W) x 15.8cm (D) x 4.2 (H) (1U)
Dimensions (Raw):
19” (W) x 6.2” (D) x 1.7” (H) (1U)
Dimensions (Boxed):
58.5cm (W) x 27.4cm (D) x 10.8cm (H)
Dimensions (Boxed):
23” (W) x 10.9” (D) x 4.3” (H)
Weight:
Nett: 1.6kg       Gross: 2.2kg
Weight:
Nett: 3.5lbs      Gross: 4.8lbs

Downloads & Resources

Support

Handbooks & Guides

RB-DA24MD HandbookDownload ↗

Firmware

No firmware currently listed.

Firmware Notes

Full release notes for all firmware versions will appear here when available.

Brochures

Brochures, guides and supporting literature are available from the Sonifex brochures library.Visit brochures page ↗

Declarations

Access CE and UKCA declarations and other product compliance documentation.Visit declarations page ↗