Mix Consoles

S2-CMM

Mic/Mic Channel

The mic/mic input channel is a dual mono microphone input with a button switch to select either Mic 1 or Mic 2.

About S2-CMM

The mic/mic input channel is a dual mono microphone input with a button switch to select either Mic 1 or Mic 2. Each Mic input has jumper settable phantom power available at +48V and a high pass filter to remove low frequency rumbles. When enabled, the LF response of the microphone is rolled off at 125kHz, 6dB per octave. If the Mic input is used for the presenter’s mic it can also become the talkback mic.

Equalisation is fitted as standard on this channel and is enabled by the EQ button, providing 10dB cut and boost at HF (6.5kHz) and LF (100Hz). The BAL/PAN control operates as follows : Full anti-clockwise pans the signal to the left and increases the signal by 3dB (right channel reduces by 70dB); full clockwise pans the signal to the right and increases the signal by 3dB (left channel reduces by 70dB).

A balanced line level insert send and return is available for the Mic input. This is useful for hooking up an outboard effects unit to be used with the microphone. There are logic remote input controls for Mic Cough muting and Reverse Talkback, together with two separate output controls for Mic Cue lights, which can be momentary or latching.

The remote outputs on the 9 way D-type plug are fed from NPN opto-isolators. Both Mic inputs have a jumper selectable output to facilitate either Control Room speaker or Studio speaker muting and the channel can also be used to control either one of two separate timer displays. Gold plated Neutrik XLR connectors are used for the audio inputs and outputs.

Typical Applications

Community, student, hospital and small scale radio broadcast mixer, secondary or backup on-air mixer.

Product Data

Technical Specifications

Input/Output Impedances
Mic Input:
> 1k5Ω electronically balanced
Mono Line Input:
> 20kΩ electronically balanced
Stereo Line Input:
> 20kΩ electronically balanced
PGM & AUD Output:
< 75Ω electronically balanced
Mono Output:
< 75Ω electronically balanced
Monitor Outputs:
< 75Ω unbalanced
AES Input/Output:
110Ω
S/PDIF Input/Output:
75Ω
BNC Wordclock input:
50Ω
Input/Output Gain Range
Mic Input:
Preset pot +13dB to +66dB ref -50dBu, TRIM pot ±12dB
Mono Line Input:
Preset pot -6dB to +10dB ref 0dBu, TRIM pot ±12dB
Stereo Line Input:
Preset pot -6dB to +10dB ref 0dBu, TRIM pot ±12dB
Telco Input:
Preset pot -6dB to +10dB ref 0dBu, TRIM pot ±12dB
Telco Output:
Preset pot -6dB to +4dB ref 0dBu
Mix Minus Input:
Preset pot -6dB to +10dB ref 0dBu, TRIM pot ±12dB
Mix Minus Output:
Preset pot -3dB to +3dB ref 0dBu
Digital Input:
0dBFS = +12dBu on input; TRIM pot ±12dB allowing 0dBu to +24dBu
Digital Output:
0dBFS = +18dBu
Frequency Response
Mic Input:
40Hz to 20kHz, -1dB,+0dB (-3dB at 130Hz with HPF in)
Line Inputs:
20Hz to 20kHz, - 0.5dB,+0dB
RIAA Input:
30Hz to 16kHz ±1.5dB RIAA equalised
Noise (20Hz to 20kHz)
Mic Input E.I.N.:
-129dB with 150Ω source
Stereo Inputs (fader down, no routing):
-89dB ref 0dB
Stereo Inputs (fader down, one channel routed):
-89dB
Stereo Inputs (unity gain, no routing):
-89dB
Stereo Inputs (unity gain, one channel routed):
-86dB
Stereo Inputs (unity gain, two channels routed):
-83dB
Distortion
Total Harmonic Distortion:
0.015% at 1kHz, 0dB
Total Harmonic Distortion:
0.025% at 10kHz, 0dB
Crosstalk
Inter-channel:
< -90dBu
Stereo:
-90dBu at 1kHz
Equalisation
LF Shelving at 100Hz:
±7dB
HF Shelving at 6.5kHz:
±7dB
Range
Pan Range:
off/-3dB centre/off
Balance Range:
±6dB
Common Mode Rejection Ratio
Mic Input:
> 100dB at 70dB gain
Digital I/O
Sync Input Sample Rate:
30kHz - 100kHz
Output Sample Rates (Using Onboard Clock):
32kHz, 44.1kHz, 48kHz, & 96kHz
Output Sample Width:
16, 20, 24 bit (24 bit on V2 ODA/ODP)
Output
Headphone Output Load:
>45Ω, 400Ω recommended
Maximum Output (Analogue):
+26dBu balanced into 2kΩ or greater
Power
Power (S2-PSU):
Filtered IEC, switchable 115V, 230V, fused, 210W max.
Dimensions (S2-PSU):
48cm (W) x 24.3cm (D) x 8.8cm (H)
(Raw):
19” (W) x 10” (D) x 3.5” (H)
Dimensions (S2-PSU):
51cm (W) x 41.5cm (D) x 17cm (H)
(Boxed):
20” (W) x 16.3” (D) x 6.7” (H)
Weight (S2-PSU):
Nett: 6kg       Gross: 7.8kg
Weight (S2-PSU):
Nett: 13.2lbs Gross: 17lbs
Dimensions (S2-PSUS):
48cm (W) x 23cm (D) x 4.4cm (H)
(Raw):
19” (W) x 9” (D) x 1.7” (H)
Dimensions (S2-PSUS):
55cm (W) x 39.3cm (D) x 8.5cm (H)
(Boxed):
21.6” (W) x 15.5” (D) x 3.4” (H)
Weight (S2-PSUS):
Nett: 1.58kg Gross: 2kg
Weight (S2-PSUS):
Nett: 3.5lbs  Gross: 4.4lbs

Downloads & Resources

Support

Handbooks & Guides

S2-CMM HandbookDownload ↗

Firmware

No firmware currently listed.

Firmware Notes

Full release notes for all firmware versions will appear here when available.

Brochures

Brochures, guides and supporting literature are available from the Sonifex brochures library.Visit brochures page ↗

Declarations

Access CE and UKCA declarations and other product compliance documentation.Visit declarations page ↗